JMSMotorsport
Members-
Posts
99 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Everything posted by JMSMotorsport
-
NA+T conversion, merged a BA XR6T map to my ECU in a XE, Having trouble to get it to idle at commanded. Starts off fine but then as it runs the AFRs starts going rich, doesn’t matter how much I increase the Slope table at idle there’s no improvement, it’s at a point now that off idle it’s lean. i gather I’m missing a idle fueling table somewhere? Can anyone point me in the right direction.
-
Common Strategies and Catchcodes
JMSMotorsport replied to Roland@pcmtec's topic in Falcon HOWTO Guides
Done mate -
Common Strategies and Catchcodes
JMSMotorsport replied to Roland@pcmtec's topic in Falcon HOWTO Guides
HACCKD5 that would be super helpful. -
Common Strategies and Catchcodes
JMSMotorsport replied to Roland@pcmtec's topic in Falcon HOWTO Guides
Thanks mate. Xcel finally decided to work. Found it then realised no 4speed turbo in the BF so as far as I am aware, I just need to manually transfer everything from a BF 6Speed turbo file bar the trans stuff. -
Common Strategies and Catchcodes
JMSMotorsport replied to Roland@pcmtec's topic in Falcon HOWTO Guides
Trying to find the Strategy for a BF XR6T? Trying to convert my BF NA conversion to turbo that's in a XE Falcon. Is it best to just merge a turbo file with my already licensed files as ABS etc isnt an issue? -
All good left it disconnected for an hour and cam back to life flashed in full pats removal and everything doing what it should
-
Building a XE Barra conversion. Had everything working read the ECU out twice, then flashed in a PATS disabled File. But only done one of the PATs tables missed the other one. Now when I try to flash in the new file I get a connection error. Tried a recovery and get the same error? Any ideas have I bricked the ECU?
-
When I first connected and downloaded the stock file it was set for VRS via wire and control was undefined. Must be a glitch when it first gets the VID block data.
-
Managed to get it sorted. Made a plug that fits The BA cradle on outside and FG sensor inside and spaced out with a thick washer. Had to change the speed control to ABS CAN and intergrated control.
-
Funny thing is no ABS fault on dyno, took it off to see if that was issue with cruise. Cruise stopped flashing but then triggered the ABS fault. Looks like I will have to make some form of adapter for the FG sensor into BA cradle.
-
Well might have found a problem. FG with complete BA rear cradle so had adapted BA ABS Sensor to FG plug. Except now I get a ABS fault not coherent abs sensors left and right rear. Is there any where to alter the sensor calibration data to suit BA sensors?
-
Having some trouble with a 2009 FG XR6 With the 5 speed trans, have modified the VID block to correct speedo after diff gear change. Now cruise comes up and just flashes, I have speed control enabled, Speed control source - VRS Via Wire and Speed control type - Non Intergrated. This stopped the cruise flashing and now sets but it won’t hold it tries to then just turns off. Mind you this is on a dyno so could that be because the front wheels aren’t moving? Or should it be set up different?
-
Rolan, only thing I’ve missed is the offset table what’s the number of this in the software so I can do a search. thanks.
- 42 replies
-
- speed density
- map
-
(and 1 more)
Tagged with:
-
Indeed the Variable camshaft Timing adds a large degree of changes in VE and as you say would be a nightmare to tune this system that way. I had good results tuning the slope table on a XR6T but the non variable V8 threw me but as explained seems straight forward.
- 42 replies
-
- speed density
- map
-
(and 1 more)
Tagged with:
-
Thank you, that’s a great explanation. Coming from GM based VE tuning it’s a much different world in the Ford ECM.
- 42 replies
-
- speed density
- map
-
(and 1 more)
Tagged with:
-
Ah yep, so basically you tune this single axis table at say wot on a ramp run and then every other load area is worked out by the pcm’s algorithms. That’s a bloody good system.
- 42 replies
-
- speed density
- map
-
(and 1 more)
Tagged with:
-
Where does the load axis come from? As Cruise and WOT will be different fuelling requirements.
- 42 replies
-
- speed density
- map
-
(and 1 more)
Tagged with:
-
Is it the same process for the V8? Obviously no VCT so do you just alter all the cam angles in Auf0061? Also a injector slope tuning question is this required on stock injectors or only if changing to bigger ones.
- 42 replies
-
- speed density
- map
-
(and 1 more)
Tagged with:
-
Perfect answer, i thought could use one or the other but wanted to clarify.
-
What is the main channel to log to see knock occurring? Also when tuning the spark tables am I altering the MBT or Knock Edge Spark Tables or Both? Thanks.
-
I’m chasing an issue with a BA XR6T, Completely stock apart from a FG Turbo and a Dump back exhaust system. It will get to around 3500-4000 rpm and then just falls flat and cuts out. I’m guessing it’s overboost. If I zero the wastegate duty should this then just open under wastegate spring pressure to help me determine if it is boost cut or something else?