BeerTurbo Posted August 12, 2018 Share Posted August 12, 2018 Howdy today i decided to fix the clock spring in the daily, it only been a year - but who's counting. anyway its a base model XT BA falcon ute. I have since added the cruise control buttons to the steering wheel and the different brake sensor that is apparently required for cruise control. The cruise control does not work, so i went in PCMTECH to see whats up. auF0390 - Cruise Control Switch - is set to 1 (Hardware present switch for Vehicle Speed Control system (Cruise Control)) Stock is one so i figgure its right, or? Quote Link to comment Share on other sites More sharing options...
BeerTurbo Posted August 12, 2018 Author Share Posted August 12, 2018 Just went and fixed all the brake light situation, as a forum post said no cruse control without working brake lights - still no go. http://www.performanceforums.com/forums/showthread.php?67281117-Early-BA-Falcon-Ute-questions Quote Gday guys cruise activation can be done by anyone with a Ford IDS Scanner and the relevant software, it is available in the programmable parameters section or the module programmer under speed control. if you need it done we can do it. We sell kits for $160.00 plus $100.00 fitted and programmed. if you fit them and just want it programmed we charge $35.00 cheers Stuart (08) 8341 1122. In answer to your question territorys are the same in fact most of the territorys that have come in to us already have the correct brake switches you just need to add the steering wheels switches. dont be fooled you do not need two keys to progam speed control it just adds a parameter it does not activate the PATS.hope this helpsBSM is that any help, i cant see anything in that subsection that is obvious Quote Link to comment Share on other sites More sharing options...
Roland@pcmtec Posted August 13, 2018 Share Posted August 13, 2018 On 8/12/2018 at 3:03 PM, BeerTurbo said: Just went and fixed all the brake light situation, as a forum post said no cruse control without working brake lights - still no go. http://www.performanceforums.com/forums/showthread.php?67281117-Early-BA-Falcon-Ute-questions is that any help, i cant see anything in that subsection that is obvious I've never tried doing this sorry. I suspect you need to use IDS to reprogram the BCM/ICC etc to expect these signals and ensure the data is passed back onto the PCM. As far as I know these signals don't go to the PCM but rather another module, it then sends this data back to the PCM via canbus. I could be wrong however. Quote Link to comment Share on other sites More sharing options...
Darryl@pcmtec Posted September 25, 2019 Share Posted September 25, 2019 Before you start on trying to find out if there is anything wrong with the calibration on a car that was working please ensure the Brake Switch and Clutch switches are working properly. It is quite common that they fail and the cruise control will not operate if either of these switches is on. Quote Link to comment Share on other sites More sharing options...
boostedfalcon Posted January 11, 2022 Share Posted January 11, 2022 On 8/13/2018 at 6:04 PM, Whiteford said: Thanks Roland, The cruise control is set within the PCM VID Block (F0390) is correct, however other factors will contribute to its operation. Some other parameters to look into include F16617, F0392 etc. These can all be located within the VID Block. Some key things to remember with Cruise Control are the tire size, wheel rotation and differential ratio. Make sure these are set to what is fitted to the car. If these are incorrect, the cruise control will never work. Two readings you will need to data log are Brake Boost Pressure and Brake Light Switch activation. If the PCM reads any Brake Pressure applied from the ABS Module or the Brake Lights activated, this will also cause the cruise control to not engage. As far as IDS is concerned, depending on the PCM calibration, there is only one setting that can be adjusted as pictured below. i had a similar issue, i found in the vid block i had to change speed control to enabled from unconfigured speed control type to basic intergrated from unconfigured problem sorted 2 1 Quote Link to comment Share on other sites More sharing options...
05ENFORCER Posted July 8, 2022 Share Posted July 8, 2022 Fixed my cruise control problem in FGX, Cheers. Quote Link to comment Share on other sites More sharing options...
BeerTurbo Posted August 7 Author Share Posted August 7 On 1/11/2022 at 5:43 PM, boostedfalcon said: i had a similar issue, i found in the vid block i had to change speed control to enabled from unconfigured speed control type to basic intergrated from unconfigured problem sorted Gday mate. i never did get my ba cruse working as i sold the car .... but ive gone full circle and acquired a territory without cruse control. i just installed the buttons and it already had the two brake switches.... changed the two options you mentioned and walah works fine. so i know its bit late, but thanks. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.